Home/Moulds/Blow moulds/Detergent bottle blow mould

Handle, grip and neck

Detergent bottle blow mould, handle blown in

On a detergent bottle mould with a handle, the hard part is not the body. It is the handle. The handle loop is where the parison is pinched and blown out, so the wall there, the risk of cracking and how cleanly the flash in the handle comes away are largely settled when the tool is cut.

Nine handled-bottle tools in our files, 500 ml to 5 L, every one ordered with auto-deflashing.

ProcessExtrusion blow
Lead time25–35 days
Cavities1 or 2, set by your output
MaterialHDPE

Send your bottle drawing Look at the tool

Only have the bottle? Photograph it from every side and tell us the volume.

WhatsApp +1 773-386-2484

A white 5 L handled bottle coming out of one of our extrusion blow moulds after a tryout shot.

Blow moulds — lead time25–35 daysCounted from the approved drawing.

Trial parts ship with the toolMoulded on our own machine and packed in the same crate.

Get an exact quote within 24–48 hoursAn itemised price for your part.

Moulds cut in-houseOur own mould workshop in Jiangsu, China, running since 2007.

The tool itself

Two of our detergent bottle moulds at tryout

Tryout footage of a 5 L and a 500 ml handled-bottle mould from our workshop.

The 5 L tool at tryout. The mould closes on the parison and pinches it off at the top.

A 500 ml bottle mould at tryout. A red tryout bottle: the parison at the mould, the mould opening, and the handled bottle taken out.

Drawings from our files

Detergent bottle drawings, 500 ml to 5 L

Drawings from our handled-bottle tools, 500 ml to 5 L, in our files. The figures in each caption are taken from that drawing, tolerances included.

500 ml detergent bottle mould

Drawing of a 500 ml detergent bottle with handle: 540 ± 10 ml brimful, 44 ± 1 g, 211 ± 2 mm high — **500 ml handled bottle.** 44 ± 1 g, 540 ± 10 ml brimful, 211 ± 2 mm high, 0.92 mm average wall. Three-start neck thread, 3 mm pitch, 9 mm lead, Ø38 ± 0.25 mm.

Drawing of a second 500 ml handled bottle: 645 ± 8 ml brimful, 48 ± 1 g, 215.5 ± 2 mm high — **A second 500 ml design.** 48 ± 1 g, 645 ± 8 ml brimful, 215.5 ± 2 mm high. Three-start neck thread, 3 mm pitch, 9 mm lead, Ø37.7 ± 0.3 mm; a round raised-dot pattern is marked on the sheet.

1 L detergent bottle mould

Drawing of a 1 L detergent bottle with handle: 1115 ± 15 ml brimful, 67 ± 3 g, neck Ø66 ± 0.4 mm — **1 L handled bottle.** 67 ± 3 g, 1115 ± 15 ml brimful, 176.4 ± 1.7 mm high. Two-start neck thread, 4 mm pitch, 8 mm lead, Ø66 ± 0.4 mm.

3 L detergent bottle mould

Drawing of a 3 L detergent bottle with handle: 3415 ± 25 ml brimful, 124 ± 3 g, 340.4 ± 3 mm high — **3 L handled bottle.** 124 ± 3 g, 3415 ± 25 ml brimful, 340.4 ± 3 mm high.

Drawing of a second 3 L handled bottle: 3105 ± 20 ml brimful, 145 ± 5 g, 335 ± 3.3 mm high — **A second 3 L design.** 145 ± 5 g, 3105 ± 20 ml brimful, 335 ± 3.3 mm high.

5 L detergent bottle mould

Drawing of a 5 L PE detergent bottle with shaded views: 5376 ± 50 ml brimful, 181 ± 3 g, 345.5 ± 3.5 mm high — **5 L detergent bottle.** PE, 181 ± 3 g, 5376 ± 50 ml brimful, 345.5 ± 3.5 mm high.

Drawing of a 5 L handled bottle: 5400 ± 50 ml brimful, 180 ± 4 g, 0.95 mm even wall — **A second 5 L design.** 180 ± 4 g, 5400 ± 50 ml brimful, 353.9 mm high, 0.95 mm even wall. Single-start neck thread, 3.6 mm pitch, Ø41 ± 0.3 mm; raised grip dots on the handle are marked on the sheet.

Part drawing of a 5 L bottle with a blown-in handle: neck thread, handle section and base dimensions — The part drawing behind the 5 L tool in the footage above: neck thread, handle section and base, all dimensioned.

What comes off it

HDPE bottles with handles, off our moulds

Photographed as they came off our moulds, not rendered. The handle is blown with the body, and the grip dots are cut into the cavity.

White 5 L detergent bottle from the side, the handle blown in with the body — The handle is formed in the tool as part of the body, not welded on afterwards.

White 5 L detergent bottle seen from the handle end, with a moulded measuring scale below the neck — The same bottle from the handle end, with a measuring scale moulded in below the neck.

White 5 L detergent bottle with round grip dots along its blown-in handle — A second 5 L design: round raised dots along the grip of the handle, and an open threaded neck.

White 3 L detergent bottle with a blown-in handle and its cap on — A 3 L bottle with its cap on, with grip dots moulded beside the handle opening.

White 500 ml HDPE bottle with a moulded-in handle and a threaded neck — The bottle from the 500 ml tool in the tryout footage above, in white: the handle moulded in and a wide threaded neck.

Have a drawing or a sample of your own? Send it and get an exact quote within 24–48 hours.Send your drawing Ask on WhatsApp

Bottle and cap, quoted together

The neck thread on the bottle and the thread in the cap have to match. Send the cap with the bottle and we quote the cap mould alongside, cut to the same thread.

Before you order

Seven questions about the tool itself

The seven that decide whether you order a bottle blow mould, answered for handled detergent bottles. Where a figure is on the drawing we print it; where it depends on your bottle we say which numbers we will ask you for.

Hot runner or cold runner?

There is no runner system on a blow mould. The parison comes off the die head, so instead of a runner choice we design the cooling and the pinch-off for the bottle you sell, and that is what the quotation describes.

Cycle time and output

Set by the bottle weight, the wall and the cooling on your machine. These tools run one or two cavities, set by your output; tell us the bottles per hour and the figure is worked out with you rather than quoted blind.

How the part is ejected

A bottle is released when the tool opens and taken out by the machine; the handle pinch and the flash are what we design. All nine tools in our files were ordered with automatic deflashing, and the deflashing arrangement is drawn before the steel is cut.

Tryout report and acceptance

The mould is fitted to a machine here and bottles are blown before it ships, and those bottles travel with it. Bottle weight, the brimful capacity or the capacity to the fill line, the drop test and the handle strength are the usual acceptance points.

Spare parts

The pinch-off inserts, the neck inserts and the deflashing cutters wear first, and they are cut from the same drawings. Say which spares to pack with the mould.

Warranty

Warranty terms are written into the quotation for that tool.

Will it fit your machine?

Send the make, model, platen size and daylight of your blow moulding machine, and the die head. The mould is designed to that machine and the fit is confirmed before cutting.

What we will ask you for: the bottle volume, the target weight, the handle shape, the neck thread and the cap it takes, the bottles per hour, and the machine.

How many bottles an hour does the line have to make?

For a handled detergent bottle this decides whether the tool carries one cavity or two, which changes the tool and the machine it needs. Tell us the output you are planning around.

Tell us your output target

Answers

Frequently asked questions

Yes. A detergent bottle has its handle on the side of the body, blown with the bottle, and a neck thread cut to its cap. A jerry can is a flat, square container with the handle on top, and its tool is built around the corners and the stacking wall. Jerry can tooling is on our jerry can blow mould page. North American buyers write detergent bottle mold, or simply bottle blow mold, for the same tool.

A handled bottle carries a lot of flash around the handle, and auto-deflashing takes it off on the machine, so the bottle leaves without a second trimming step. All nine handled-bottle tools in our files were ordered with it.

Blow moulds are delivered in 25–35 days from the approved drawing. An exact date is confirmed in the quotation.

Yes. A STEP or STL file, a PDF drawing or photos of the bottle from every side with its volume all work. Several of the tools on this page have their 3D file in our records.

Yes. Send the cap with the bottle and we quote both, with the thread in the cap cut to the neck of the bottle; see our detergent cap moulds.

Send us your bottle drawing

Attach the drawing straight to the enquiry form, with the cap the bottle takes. Only have the bottle? Photograph it from every side and tell us the volume.

✓A drawing, a STEP or STL file, or clear photos of the bottle
✓Volume, weight in grams and the handle shape
✓The neck thread and the cap it has to take
✓The machine it will run on, or the bottles per hour

Email* Name

Company Country

Phone / WhatsApp Target output

What do you need?*

Attach drawings or photos (optional) Drag files here or browse Bottle photo, drawing, 3D file (STEP/IGES/STL), PDF, Word, Excel or ZIP · up to 10 files, 25 MB each

By submitting this form you agree that we may use your details to reply to your inquiry, as described in our Privacy Policy.

WhatsApp +1 773-386-2484

Attachments go with the form. We come back with an exact quote within 24–48 hours. Prefer e-mail? sales10@amanmachinery.com